Showing results: 841 - 855 of 1086 items found.
-
Shanghai Launch Electric Co., Ltd.
The electrode is used in dielectric constant εr and dielectric loss tgδ test for solid electrical material such as insulation paint, resin, rubber, fibrillated product, laminate, mica product, plastic, cable, film composite, porcelain and glass. The electrode is designed to use under power frequency of 50Hz, and comply with international standard GB1409-78.
-
PC-1 -
Applied Instruments, Inc.
The PC-1 is a compact, temperature-stable RF-carrier source. It is accurate enough to calibrate spectrum analyzers, signal level meters or any other receiving devices. When used with a signal level meter, the PC-1 CW test signal generator assists in measuring insertion loss of cable, amplifiers, splitters, and taps using the stimulus-response method.
-
PTS Series -
High Voltage Inc.
The PTS Series can perform high voltage DC hipot/proof and current leakage testing as well as resistance measurement testing. Most models offer a high output current for quicker charging of capacitive loads like cables. Like all HVI portable test equipment, the PTS Series is designed to withstand the rigors of field use.
-
H Model -
PJ Electronics, Inc.
H models are "2 piece" versions of the Signature ("S") Models. These compact two piece portable high frequency digital surge testers come complete with a Tektronix Type TDS1002, fully digital storage oscilloscope, 10' long test cables and a soft carrying case with a shoulder strap.
-
B-1013 -
ROSS ENGINEERING CORPORATION
*25kV, 50kV or 100kV Meter with integral line to ground Probe*Phasing or line to line with additional Probe*Optional 6ft or 9ft Collapsible Hotsticks*Voltage source for testing Voltmeters and Probes*Optional test point contamination indicating Megmeter®*High voltage cable clamps or hooks*Heavy duty carrying case
-
ENVIROMUX-CO2 -
Network Technologies Inc
CO2 room sensor for periodically unoccupied areas. Measures CO2 in a range of 0 to 2,000 ppm. 0 to 5 VDC output. Continuous automatic air pressure compensation. LED indicators for operation status and system test. Maximum cable length: 1000 ft (305m). Powered by ENVIROMUX-2D/5D/16D. Regulatory approvals: RoHS.
-
M9121A -
Keysight Technologies
The M9121A is a 4x64 full crosspoint switch matrix offering high-density, high-speed signal switching in a single PXI module. The 2-wire matrix allows multiple channels to be connected in a single instance. Any row can be connected to any column, making it ideal for routing instrument signals to the device under test. This 2-wire switch matrix provides the high-speed, long-life reed relays to support signal switching up 100Vrms with 10W maximum power. The 4-wide bus is ideal to route signals between test instruments and the device under test. Choose from the durable connector block or standard cable connections.
-
N4952A -
Keysight Technologies
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
F9 Systems, Inc.
This ATCA compatible test card offers the flexibility to verify the performance of Advanced TCA fabric and base channels. The set of four Transmit pairs and four Receive pairs allows access to a full channel's eight pairs for logic card characterization. The card includes a HM-ZD male right angle connector segment for access to the Zone 2 connectors of a switch fabric or node card. Edge-launch SMA connectors are utilized for ease of test cable attachment. SMT pads are included on the receive pairs.
-
Neutronics Manufacturing Co.
NMC''s Transformer BDV Oil Test Set is a portable unit as per relevant Indian Standard Specification IS :6792 :1992, suitable for operation on 230 / 240 Volts, A.C. 50 Hz. A three core flexible cable is connected to the unit with three pin socket to connect the mains. The H.V. Transformer is a completely dry, resin encapsulated with two H.V. terminals with mounting saddles. The center point of the transformer is earthed, so that the voltage of each terminal to earth is only half the test voltage.
-
TWA Advanced Series -
Amperis sl
The TWA advanced series instruments are designed for six-winding resistance measurement and simultaneous three phase on-load tap changer analysis of both the primary and the secondary transformer windings. This is performed with a one singlestep cable setup, with test currents of up to 40A. Each transformer configuration has a special measurement algorithm which is optimized for the fast stabilization of test results. The TWA instruments generate a true DC ripple-free current. Both the injection of the current and the discharge of energy from the magnetic circuit are automatically regulated.
-
TWA Standard Series -
Amperis sl
The TWA standard series instruments are designed to measure the resistance of six coils and simultaneously analyze the three-phase tap changer on load of the primary and secondary transformer coils (provided by model TWA40). This is done in a single cable configuration, with test currents up to 40A. Each transformer configuration has a special measurement algorithm that is optimized for rapid stabilization of test results. The TWA instruments generate a true DC current without ripple. Both current injection and magnetic circuit energy discharge are automatically regulated.
-
OX-1 OxSim® -
Pronk Technologies Inc.
Test the complete SpO2 system, including the sensor, extension cable with the OxSim® Optical SpO2 Pulse Oximeter Simulator. Slips into your shirt pocket and operates easily with just two buttons on a single AA battery. The auto-detection of the Sensor type eliminates the need to select the manufacturer oximeter under test. The optional serial communications port enables users to expand simulation settings for Saturation, Pulse Rate, and Perfusion Index, ideal for applications where a wide range of simulations is needed.
-
726 -
Electronic Specialties Inc.
*Accurate Battery & Electrical System Tester *Features programmed test for new Start/Stop Batteries 3 Testers in ONE! 1) 6 & 12 Volt Battery Tester + 12V Start/Stop Battery Test 2) 12 & 24 Volt Charging System Tester 3) Alternator-Starting-Charging System Tester *Wide Testing Range from 40 to 2,000 CCA *Built-in Printer - print the results for permanent service records *Removable/Replaceable Cable Set *Patented Dynamic Resistance Technology
-
Educated Design & Development, Inc.
Up to 8 resistance reading channels, 4-wire methodUp to 12 temperature reading chanels, use of Type K, 24 AWG, Teflon thermocouplesIn the Box:8 - data cable (Cat5e) to connect the isolation modules to the Resistance Reading Channels8 - Isolation Module connected between the HOT-30 and EUT (Equipment Under Test) to isolate high voltage8 - Banana Jack Sets (2 red, 2 black), to replace Kelvin Leads in tight places8 - Kelvin Probe Set12 - 72 inch K Type Thermocouple1 - USB2.0 Type A (standard) to Type B USB cable